sE Electronics VR1

Uden moms: 2.952,90kr
3.573,00kr
Fjernlager: 1+ stk. til rådighed
Levering inden for 7-14 arbejdsdage
Tilføj til ønske liste Tilføj for at sammenligne
Varianter

Ask our experts!

Oversigt
Presented in a black finish, the sE Electronics VR1 Passive Ribbon Microphone features a hand-tensioned aluminum ribbon and passive electronics that are designed to protect the ribbon element from phantom power. It is tuned to deliver the classic sonic characteristics of ribbon mics along with the extended high-frequency traits normally associated with condenser microphones. Since it can handle high SPLs, it can be used on loud sources such as drums and guitar cabs as well as acoustic instruments.

Like most ribbons, the VR1 has a traditional figure-8 polar pattern, so it will pick up some ambient sound behind the mic. Equipped with a balanced XLR 3-pin output, the VR1 can be connected to your audio interface, mixer, or external mic preamp; one with robust gain is recommended for optimal performance. The supplied shockmount reduces vibration and stand-borne noise while providing added visual flair. A wooden case is included for safe storage between sessions.

 

Voodoo Series

Whereas many ribbon microphones have a dark, muted high-frequency response, the Voodoo VR1 utilizes a clever mechanical device to achieve nearly full-range frequency response that extends well beyond that of most other ribbon microphones, approaching nearly 20 kHz. This provides an extended level of top-end detail, so the result includes not only the distinctly natural lows and midrange that most ribbons provide, but also minimal loss in high-frequency content. Guitar and brass tones retain their edge, cymbals still sound rich and full, and a supremely natural sound is achieved from top to bottom.

Additionally, the VR1 can handle very-high sound pressure levels and thus can be utilized for applications not normally considered for most ribbon microphones, including loud brass, drums, and electric guitar cabinets, both in the studio and on stage.

 

VR1 vs VR2

The VR1 is a passive ribbon, so it does not require phantom power. However, it is "phantom-protected", so it will not be damaged by accidental application of phantom power. Given its lower output, it is ideally suited for loud sources such as electric guitars, drum overheads, and brass, or quieter sources when paired with a clean, high-gain preamp.

The VR2 is an active ribbon and requires +48V phantom power for operation. With higher sensitivity than the VR1, it is ideally suited for applications including acoustic instruments, piano, and vocals as well as the same sources as the VR1 (guitars, drums, brass).

 

Widely Used

Voodoo ribbon mics are used by these artists and many more:
  • Queens of the Stone Age
  • Billy Gibbons
  • August Greene
  • My Morning Jacket
  • Pete Thorn
  • Steve Stevens
  • John Browne
  • Neil Cappellino
  • Linkin Park
  • Band of Horses
  • Taking Back Sunday
  • Paramore
  • Black Sabbath
  • David Hodges
Funktioner
  • Hand-Tensioned Aluminum Ribbon
  • Figure-8 Polar Pattern
  • Passive Design
  • Classic Ribbon Sound with Extended Highs
  • High Max SPL Handling
  • XLR 3-Pin Output Connector
  • Shockmount Reduces Vibration Noise
  • Includes Wooden Case
Hvad er i kassen?
  • sE Electronics Voodoo VR1 Passive Ribbon Microphone (Black)
  • Shockmount
  • Mic Stand Clip
  • Thread Adapter
  • Wooden Case
Specifikationer
Microphone Type Dynamic
Mono/Stereo 2 Mono
Polar Pattern Figure-Eight
Frekvensgang 20 - 18 000 Hz
Max SPL 135 dB (0.5% THD @ 1kHz)
Impedans 300 Ω
Lydtryk 1.78 mV/Pa (-55 dB)
Signal to Noise Ratio 75 dB
Dimensioner Exterior 3.3 x 1.9 x 12.7 cm
Vægt 230 g

Instruktioner til produktet